New Version Changes
’09.11.05 V4.41b
[N090815007/ALL/ALL] TEMP LICENSE display screens in MMC 860 should be changed
[P090815002/ALL/ALL] Headset mode cannot be set or unset during conversation
[P090815001/ALL/ALL] ABW key cannot be used during phone call
[P090813001] KMMC 406 cannot be used set extension 3999 modem as trunk ring.
[P080424014/ALL/ALL] ITP5112L OVERLAP MODE OPERATION
[-/ALL/ALL] transferred call's CID from AA didn't display
When incoming call with CID is answered by the AA and then transfer to a station (eg; 203) the display of station 203 will not show [CID name and number]. Display show: "TRANS FM 701" on the second line. This is fixed
[-/ALL/ALL] can't use IT tool to assign VT key
When using software load 4.41 and IT tool version 1.40, to IT tool 4.9.2 (MMC 722) cannot be used to program an VT key on any digital or ITP phone. It’s fixed. When using KMMC programming the VT key on a key phone is not a problem.
[P090822001/ALL/ALL] Missed Calls display causes date lockup on keyset
[P090901004] MMC119 Ringing Display on Line 2 is set to None when i5243 connected
[P090728007/ALL/ALL] DND FORWARD FUNCTIONALITY OS7400
[P090808001/ALL/ALL ] Network forward 2nd Call across network
[P090902001/ALL/ALL] Set Relocate does not work between SLT extension and Virtual SLT extension
[P090818016/ALL/ALL] E-LCR & Standard SIP phones
[-/ALL/USA,RUSSIA,KOR] Changed new Keyset's License policy
Changed new Keyset's License policy
These new keysets are IP2200, IP3100, IP5220, IP5240, IP5243, WIP5120
In case of USA and Russia, you can use these keysets without license.
[-/ALL/ALL] DTMF sending through SIP trunk for dialing
If DTMF type is outband, It's possible to send DTMF through SIP trunk for dialing.
[-/ALL/ALL] SIP stack failure on the Plant Office system
Reason : The failure stopped all outgoing SIP messages from the OfficeServ, no responses were sent to REGISTER messages from WIP Phones, or from the IP-UMS. Outgoing SIP trunk calls also failed with the message “No User Response” displayed on the calling phone. The OfficeServ did not send any INVITE messages for the outgoing trunk calls.
The SIP functionality was restored by performing a reset of the system in IT Tool menu item: 6.3.1
This problem occurred twice, and appears to have been caused by changing the Peer CLI table parameter in the 5.2.12 SIP Stack/Ext/Trunk Options screen. The value of the Peer CLI table parameter was changed from 1 to 2. Changing it back to 1 did not fix the problem, only a reset solved the problem.
Modification : Whenever trying to send any SIP message for UMS interop, SIP module checks whether the callleg exists or not. When not found, simply ignores the send request from Call module.
[-/ALL/ALL] SIP Registration CALL ID bug (from SER)
Reason : REGISTER messages for multiple users must have unique Call-ID but OfficeServ has same Call-ID for multiple users.
Modification :
1.If Registration status is UnReg, each regClient detach from regClientMgr, so it can be possible for each regClient to use unique Call-ID and CSeq.
2. If Registration status is Reg, Call-ID and CSeq are stored and managed for each user.
[-/ALL/ALL] New IPP(5220,5243) LED Color Control
Modified to send both led state and color information when connecting with New IPP(5220,5243).
[-/ALL/ALL] Sometimes, call log doesn't save caller name
The caller name was showed on the incoming call but sometimes it showed " Unknown" in the call log.
Modified to send call log information again after receiving FACILITY msg.
[P090826001/ALL/ALL] No light indication for DT key that refer to SIP trunk
[-/OS7100 mp11/ALL] IP Contract Full Problem
[SEI] Set NACF to STN GRP does not work for internal call
If any station set CF for No Answer toward any STN GRP, the internal call is not forwarded to.
[OS7030/SEI] VM ports lock up
It depends on the PI feature when disabled in MMC861. It happens on both system configurations: stand alone and two cabinets, both on incoming and outgoing calls.
Procedure to reproduce it:
1. Install 2BM and 4DM boards and start OS 7030 from the default (verify PI status is set as disabled in MMC 861)
2. Enter a valid license for VM ports
3. Connect two DGPs (203 and 204)
4. Set ON both VMAREC and VREC in MMC 701
5. In MMC 752, set "AUTO RECORD" for STN: 203 - MB: 204 - PORT: 509 - CALL: B
6. Establish a call with station 203 and wait for VM port processing
7. Disconnect the call from outside and hook on station 203 within one or two seconds
8. Check VM port status (Processing or Idle)
[PC] Keep displaying "access denied" and error tone when accessing SIP phone info in MMC842.
When accessing MMC842 (SIP Phone Information) via keyset the screen displays "access denied" and an error tone is heard but the screen then cycles again showing "access denied". This continues and cannot be stopped by pressing SPKR key.
[PC] Lights on SMT-i5220
An issue with the LED on keys 18-24 do not light when used for DS or IG (group Log IN/Out) operation. Key operates correctly except for LED status
OS7400 V4.42a 09-10-09
SMT-i5220 V1.40
[OS7030/PC] Dial Number Plan defaults on 2nd Cabinet after System Power off / on
Steps
1) On a 2 cabinet system change DLI and TRK numbering as per above using KMMC
2) KMMC 817 (memory stop) set to Yes
3) After completion Disable KMMC
4) Power Off then back On the 2 x cabinets
5) View Dial number plan = Correct
6) Re-Power the system cabinets Off then ON
7) View Dial number plan for Cab 2 =Incorrect
Result Cabinet 2 DLI and TRK have returned to default numbering
NOTE: The extn names will stay correct on the screen
Only the Extn or trunk number will change back to default
[OS7100/MIA,SEUK] ATRK call drop
They will be talking on a call and then they will get disconnected, the phone will show the call is still active on the screen so the time will be running but remotely the trunk is disconnected.