Форум - Офисные АТС

I need procedure for upgrade to MEM4 card

Can we help me about this procedure...???

Regards,

It is possible using SIO commands and LAN with OSM100 - File Upload (off-line). This is same method with OS12 or TEPRIa/TEPRI2 upgrade via LAN and SIO. Just password for SIO bootmenu menu is "os100samsung"..
The steps is simple...
1) Connect SIO and LAN cables
2) Set SIO connectio parameters for PC.
2) Restart MEM4 card
3) Break in the proper moment the boot process by pressing enter and input the password
4) Set temp for boot mode TCP/IP parameters for MEM4 (input help command for detailed commands detailed description)
5) Input the "load" command
6) Upload the PGM file with OSM100 off-line menu
7) Restart the MEM4 with new s/w version.

This is the example for TEPRIa/TEPRI2 cards upgrade (all is same except the password)


Let the TEPRI card restart by pressing reset button in front of TEPRIa/TEPRI2 card.

[Boot PGM] <<< Boot Program of TEPRI System >>> TEPRI BOOT V1.04: 2005/10/25
[Boot PGM] Read netinfo from eeprom
- IP : 255.255.255.255
- GW : 255.255.255.255
- SM : 255.255.255.255
- MAC: 0000F0E8222E
[Boot PGM] !!!Warning: There are No assigned IP Configuration (Default IP Address is set)
[ B S P] LTX972 PHY INIT : PASS

[Boot PGM] RTCS creation is OK!
[ENTER] Press [enter] key at this point.
[Boot PGM]!Sorry, invalid password...

[Boot PGM] STOP the load to DRAM by Consol command
[Boot PGM] Enter password !

[Boot PGM]!Sorry, invalid password...

[Boot PGM]!Sorry, invalid password...
teprisamsung Input it as password
*******************************************************************************
* TEPRI Consol command help ... IAP Development Group *
* [Version: TEPRI BOOT V1.04: 2005/10/25] *
*-----------------------------------------------------------------------------*
* HELP ... TEPRI help command *
* LOAD ... File upload from PCMMC via lan interface *
* READIP ... Network parameter infomation display(IP,MAC ...) *
* WRITEIP ... Network parameter write(IP addr + Auto setting) *
* ex) WRITEIP 160.217.70.9 *
* WRITEIP2 ... Network parameter write(IP addr + Gateway addr + subnet mask) *
* ex) WRITEIP2 160.217.70.9 160.217.70.1 255.255.255.0 *
* MACR ... MAC address read *
* MACW ... MAC address write(Only MAC addr) *
* ex) MACW FF 34 56 *
* RESET ... Restart Card *
* FORMAT ... Format NOR Flash Memory *
* VER ... S/W version display *
* LMEM ... Dump memory(list memory) ex) LMEM st_addr (end_addr) (w/l) *
* WMEM ... Modify memory(write memory) ex) WMEM addr val (b/w/l) *
* *
*******************************************************************************

[Boot PGM] !!!Warning: There are No assigned IP Configuration (Default IP Address is set)
[Boot PGM] System Network Configuration
- IP : 165.213.176.141 This is the default IP address of TEPRIa/TEPRI2 card and you may need to
change it by WRITEIP command to match your network or PC.
- GW : 165.213.176.1
- SM : 255.255.255.0
- MAC: 0000F0E8222E
[Boot PGM] Invalid Command
WRITEIP 165.213.176.111 If you want to change the IP address. In order to upgrade
TEPRIa/TEPRI2 software through LAN port, you need to set IP address
to match to your network or PC.

[Boot PGM] System Network changed
- IP : 165.213.176.111
- GW : 165.213.176.1
- SM : 255.255.255.0
- MAC: 0000F0FF2468
[Boot PGM] !!! After card restart, this network information is valid
[Boot PGM] Invalid Command

load when you want to upload the PR2_xxx.pgm file to TEPRIa/TEPRI2
[Boot PGM] System Network changed
- IP : 165.213.176.111
- GW : 165.213.176.1
- SM : 255.255.255.0
- MAC: 0000F0FF2468

LionB:

1) Connect SIO with 9600-N-8-1 and reset MEM4 but not display option for break boot, only display information when LAN START
2) Version MEM4 is v1.38

Can you help me about this problem...???

Excuse me Felipe.. I'm explaning the OS100 (MP1 card), but MEM4 is iDCS100.. It is another way... Just use on-line PGM file upload menu from PCMMC v3.04 for MEM4 v1.43..

I have upgrade successful

Thanks LionB

My congratulations!