OS7200 v4.11
Добавлено:
30 авг 2007, 14:56 Wi$e
Добавлено:
30 авг 2007, 15:27 Wi$e
MCP S/W changed items
Wireless IP phone license was deleted by request.
- According to the VoIP License Policy, VoIP Stack License was added in OS7200 MCP V4.10.
But wireless IP phone license was deleted in this version by request.
- WIP PHONE can not assign in MMC841 SIP STACK ALLOW option.
- Maximum 32 wireless IP phones are available without license.
Added Features & Modified items
- Added some features and Changed some default values for IP phone’s voice quality.
MMC835 “DUAL FILTER EC” option was added.
- This option is only available in MGI16/MGI64 card.
: MGI16/ 64 should be modified, and it will be applied from later than V1.19
- Dual filter echo canceller’s parameter of MGI16/MGI64 card will be downloaded differently according to the trunk’s type.
: If this parameter is changed ‘DISABLE <-> 8TRK/8TRK2/DTRK’, MGI Card will be restarted. If this parameter is changed among 8TRK, 8TRK2, DTRK. MGI Card will not be restarted.
- ‘DISABLE’ Mode is Standard EC Mode.
- ‘8TRK’, ‘8TRK2’, ‘DTRK’ modes are Dual Filter EC Mode and only the parameters of mode are different.
- Default – 8TRK2 MODE
- Range – DISABLE, 8TRK MODE, 8TRK2 MODE, DTRK MODE
MMC841 “ITP MAX TX LIMIT” option was added
- If this option is set to YES, maximum TX level of IP phone can be limited.
- Default – NO
- Range – YES / NO
SIDETONE VOL’s default data for ITP was changed to 4 in MMC807.
MIC TX LEVEL’s default data for ITP was changed to 3 in MMC807.
Some T-SWITCH GAIN default data were changed in MMC809.
ITP <-> ATRK : 0
ITP <-> DTRK : 0
- QSIG Time synchronization feature was added.
When several systems are connected in network with the using of QSIG in TEPRI or VoIP, time synchronization will work.
MMC820 “TIME SYNC” option was added.
(Default – OFF / Range – OFF/ON)
This option does not need in SELF, only can assign from SYS(01) to SYS(99).
If the user want to use SYS(01) system to time master, TIME SYNC option of SYS(01) have to change ON. And then when other system’s station connected in network make a call to SYS(01), time will be synchronized by SYS(01)’s time.
- C-M&A Feature was added in RUSSIA
Добавлено:
30 авг 2007, 15:32 Wi$e
- Change Notes
1. When the country is set, the cid configuration is fixed.
=> We add the MMC to configure the standard of cid, receive level,
transmission level and the coding rule.
2. Four kind of new cards are developed.
=> We developed the new cards and add the interface routine for new cards.
3. Dial Pulse feature of TRK cards(16TRK and 8TRK2) is required.
=> We add Dial Pulse feature to 16TRK/8TRK2.
4. If user cancel MW when SLT's lamp is on, the lamp is not off.
=> We add the condition to blink control routine.
5. If TEPRIa card is E1/T1 mode, system can't display TEPRI version correctly.
=> We modify routine to process version information over 0x20.
6. CID receiver did not work within 5 sec after hook-on in New Zealand.
=> We add non-PRS feature to condition.